DigiTrak F5 Transmitters

DigiTrak F5® transmitters are available in five unique frequencies for maximum interference reduction. Two single-frequency transmitters and two dual-frequency transmitters are offered, in addition to two dual-frequency fluid pressure transmitters (FPT). F5 transmitters work with F5 systems only.
Part # Label Color Model/Type
F5Dpx 19/12 Yellow FPT XR dual frequency
F5DLpx 19/12 Yellow FPT XR 19" dual frequency
F5Dp 12/1.3 Light Gray FPT dual frequency
F5D 19/12 Light Blue HDT dual frequency
F5D 12/1.3 Brown HDT dual frequency
F5X 18 Magenta HDT Single frequency
F5X 8 Orange HDT Single frequency

All DigiTrak F5 transmitters provide pitch, depth, and roll readings, with 0.1% pitch sensitivity and roll data transmitted using a 24-position clock. DigiTrak F5 transmitters are battery powered and enter sleep mode after 15 minutes of inactivity. The F5 locating system is also compatible with F Series™ transmitters and 12-kHz DucTrak™ transmitters.


F5 Fluid Pressure Transmitters

The long-range DigiTrak F5 Fluid Pressure Transmitter (Model FPT) provides downhole fluid pressure monitoring up to 250 psi (1725 kPa). The drilling fluid pressure is measured through sensor ports located on the front end cap on either side of the index slot. The FPT is available in two dual-frequency configurations:  19.2 kHz/12 kHz and 12 kHz/1.3 kHz.  These transmitters have light-green tubes and incorporate a new mechanical design, in addition to the fluid pressure sensors.  The new design has a knurled battery cap that is not flush with the battery compartment, as the older version was.  With the cap installed, the overall length is still 15 in. (38.1 cm), but without the cap the length is 14.6 in. (37.08 cm).  Thus, the FPT transmitters are compatible with existing drill housings that accommodate 15 in. (38.1 cm) DigiTrak transmitters.  If using a tooling adapter, however, the new design will require a different adapter.  Also, the housings must allow fluid to flow to the sensor ports for measurement of the drilling fluid pressure.

Part # F5Dpx 19/12 F5Dp 12/1.3
Depth Range 65 ft
19.8 m
65 ft
19.8 m
Frequency 19.2 kHz or
12 kHz
12 kHz or
1.3 kHz
Battery Type
(hours awake/asleep)
2 C-cell alkaline (20/200), or
1 SuperCell (70/400), or
2 SAFT LSH14 (40/400)
2 C-cell alkaline (20/200), or
1 SuperCell (70/400), or
2 SAFT LSH14 (40/400)
Maximum Temperature 220° F
104° C
220° F
104° C
Length x Diameter 15 x 1.25 in.
38.1 x 3.175 cm
15 x 1.25 in.
38.1 x 3.175 cm
Weight 1.65 lb
748 g
1.65 lb
748 g
Housing Requirements

The FPT is compatible with existing drill housings that accommodate 15 in. (38.1 cm) DigiTrak transmitters. However, the FPT requires a path for fluid to flow from the annulus around the housing to the four sensor ports in the front end cap; slots in the housing will satisfy this requirement. If the slots are epoxied, then a 0.125 in. (3 mm) diameter hole must be installed to allow fluid pressure to be measured by the FPT. The slots in the drill head must meet minimum length and width requirements and be correctly positioned. DCI’s transmitters require a minimum of three slots equally spaced around the circumference of the drill head for optimal signal emission and maximum battery life. Measure slot lengths on the inside of the drill head; slots must be at least 1.6 mm (1/16 in.) wide. DCI transmitters fit standard housings but may require a battery cap adapter in some cases.

F5® Fluid Pressure Transmitter Diagram


F5 Dual-Frequency Transmitters

The F5 dual-frequency transmitters (Model HDT) come in two configurations:  19.2 kHz/12 kHz and 12 kHz/1.3 kHz.  These transmitters have light-green tubes and incorporate the new mechanical design like that used for the fluid pressure transmitters.  The new design has a knurled battery cap that is not flush with the battery compartment, as the older version was.  With the cap installed, the overall length is still 15 in. (38.1 cm), but without the cap the length is 14.6 in. (37.08 cm).  Thus, the HDT transmitters are compatible with existing drill housings that accommodate 15 in. (38.1 cm) DigiTrak transmitters. If using a tooling adapter, however, the new design will require a different adapter. 

  F5X8
Part # F5D 19/12 F5D 12/1.3
Depth Range 65 ft
19.8 m
65 ft
19.8 m
Frequency 19.2 kHz or
12 kHz
12 kHz or
1.3 kHz
Battery Type
(hours awake/asleep)
2 C-cell alkaline (20/200), or
1 SuperCell (70/400), or
2 SAFT LSH14 (40/400)
2 C-cell alkaline (20/200), or
1 SuperCell (70/400), or
2 SAFT LSH14 (40/400)
Maximum Temperature 220° F
104° C
220° F
104° C
Length x Diameter 15 x 1.25 in.
38.1  3.175 cm
15 x 1.25 in.
38.1 x 3.175 cm
Weight 1.7 lb
771 g
1.7 lb
771 g
Housing Requirements

The HDT transmitters are compatible with existing drill housings that accommodate 15 in. (38.1 cm) DigiTrak transmitters.  The slots in the drill head must meet minimum length and width requirements and be correctly positioned. DCI’s transmitters require a minimum of three slots equally spaced around the circumference of the drill head for optimal signal emission and maximum battery life. Measure slot lengths on the inside of the drill head; slots must be at least 1.6 mm (1/16 in.) wide. DCI transmitters fit standard housings but may require a battery cap adapter in some cases. 

F5® Fluid Pressure Transmitter Diagram


F5 Single-Frequency Transmitters

DCI's F5 single-frequency transmitters have light green tubes and share the same dimensions as other DigiTrak transmitters. They come in two frequency designations: 18.5kHz and 8.4 kHz. These transmitters are only for use with the F5 locating system.

 F5X18 F5X8
Part # F5X 18 F5X 8
Depth Range 65 ft
19.8 m
65 ft
19.8 m
Frequency 18.5 kHz 8.4 kHz
Battery Type
(hours awake/asleep)
2 C-cell alkaline (20/200), or
1 SuperCell (70/400), or
2 SAFT LSH14 (40/400)
2 C-cell alkaline (20/200), or
1 SuperCell (70/400), or
2 SAFT LSH14 (40/400)
Maximum Temperature 220° F
104° C
220° F
104° C
Length x Diameter 15 x 1.25 in.
38 x 3.175 cm
15 x 1.25 in.
38 x 3.175 cm
Weight 1.4 lb
635 g
1.4 lb
635 g
Housing Requirements

DCI's F5 single-frequency transmitters have the same design as earlier DigiTrak transmitter models and are compatible with existing drill housings that accommodate 15 in. (38.1 cm) DigiTrak transmitters.  The slots in the drill head must meet minimum length and width requirements and be correctly positioned. DCI’s transmitters require a minimum of three slots equally spaced around the circumference of the drill head for optimal signal emission and maximum battery life. Measure slot lengths on the inside of the drill head; slots must be at least 1.6 mm (1/16 in.) wide. DCI transmitters fit standard housings but may require a battery cap adapter in some cases. 

F5™ Transmitter Diagram